Peachtree Woodworking Supply

79 / 208

Your One Stop Supply Shop” 79
Spending a lot of time tightening and loosening knobs on your jigs and fixtures?
Our exclusive cam clamps will solve your problem and give you a quick release for
all of your jigs and fixtures. Cam clamps come with a standard 3”long hex head bolt
that works with ourT-track, or you can swap it with a bolt fromone of your own jigs.
Each camwill exert up to 400 pounds, depending on how you set it.
0964 1/4”x 20 TPI cam......................................................................................................... $6.99
0965 5/16” x 18 TPI cam..................................................................................................... $6.99
0966 3/8”x 16 TPI cam........................................................................................................ $6.99
Use as a quick
release hold
down
1038 (A) miter track cross points ....................................................................................$11.99
1039 (B) 1/4”mini track cross points............................................................................... $9.99
1040 (C) 3/8”HD track cross points ............................................................................... $10.99
T-track & Accessories
T-Track Cross Points
Cam Action Hold Down
Hold Down Clamps
slide into T-Track and
quickly secures with the turn
of the knob. By turning the clamp
head 180° to the work piece, the clamp
offers a dual capacity of 0”to 2”on one side
and 0”to 3”on the other side. Once the track is installed on your router table / drill
press table, you can utilize these hold downs for maximum holding pressure. Track
Not Included. The Rubber Tipped Hold Down Clamps feature non-marring rubber tips
that are the perfect tool for working with softer woods or finished surfaces. The tips
also give youmore gripping power . Hold downs come with a star knob and 3" bolt.
(see page 78 for track lengths).
1145 1 each Mini hold down (1/4”x 20 bolt)................................................................. $5.99
1146 1 each Heavy Duty hold down (3/8”x 16 bolt).................................................. $6.99
1162 1 each rubber tipped Mini hold down (1/4" x 20 bolt)................................$7.99
1163 1 each rubber tipped Heavy Duty hold down (3/8" x 16 bolt) ....................$7.99
T-Track Hold Downs
Makeyour
ownshop
built
elliptical jig
Keep your drill
press workpiece
in place
Our 4 piece T-track cross points allow you to easily make T-track intersections
for many different applications in your workshop. They work especially well on a
wooden drill press and bandsaw tables, and they can be used to build home made
oval jigs or elliptical jigs for cutting circles. Each aluminum section is cut to 1-1/2”in
length with the ends angled at 90 degrees for a perfect right angle fit. The pieces
are pre-drilledwith two holes in each section. Also includes eight mounting screws.
This all aluminum stop will put your cuts right on the money time after time. The
Flip Stop slides into your t-slot track and is secured with the top locking knob. The
stop flips out of the way if you need tomake an odd cut in themiddle of a run. Avail-
able in two different sizes: 1/4" (for1/4"minit-slottrack) and 3/8" (for3/8"Heavydutyt-slottrack).
1105 Flip stop for 1/4" Mini t-slot track . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$13.99
1104 Flip stop for 3/8" Heavy Duty t-slot track . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$13.99
Mini Flip Stop for T-slot Track
Flip Stop for T-slot Track
Repetitive cuts are easy with this flip stop on your fence. Finger tighten knob al-
lows quick adjustment while the flip away stop allows end trimming of longer piece
prior to final cut to length. Requires a minimum fence height of 2-5/16". Fits T-track
accepting 7/16" width fasteners (1/4" bolt size) for the Mini T-track and 1/2" width
fasteners( 3/8" bolt size) for Heavy Duty T-track.
2992 Flip Stop for 1/4" Mini T-Slot Track...........................................................................$14.99
2991 Flip Stop for 3/8" Heavy Duty T-Slot Track............................................................$14.99
Makerepetitive
miter cutseasy
withtheMini
FlipStop A B
C
1094 (A) 24” "L" fence - no holes.................. $17.99
1095 (A) 32” "L" fence - no holes.................. $22.99
1096 (A) 48” "L" fence - no holes.................. $34.99
1097 (B) 24” pre drilled "L" fence ................. $24.99
• 3/8”slots milled on 9”centers
• ideal for drill press fence
1063 (C) 24”pre milled/drilled "L" fence.... $24.99
• 3/8”slots milled on 9”centers
• 3-1/2”W x 1-1/2”D milled center hole
• ideal for 24”router table fence
1098 (C) 32”pre milled/drilled "L" fence.... $29.99
• 1/4”slots milled on 21½”centers
• 3-1/2”W x 1-1/2”D milled center hole
• ideal for 32”router table fence
Fence Styles
A Customize to your needs
B Ideal for drill press table fences
C Ideal for router table fences
Aluminum“L” Fences
The Aluminum “L” Fence is a
solid piece of extruded alu-
minum that can be used for
many different fence systems
like router tables, drill press
tables and bandsaw tables.
Mount independent fence
sections (not included) to cre-
ate one "solid" fence, this al-
lows you to slide and shim the
fence sections. The "L" fence is
available pre-drilled or solid in
various sizes. Fences can be
clamped to any table surface.
Pre-drilled fences can mount
to T-tracks with knobs and
bolts (not included).
3/16”
3”
2”
Pleasenote:Dimensionsmayslightlyvary
A
B
C