T-Track & Accessories

×

Double Cut Universal Track 2 Pack

with Intersection Kit

Made from a single piece of anodized extruded aluminum, each of the Fulton T-tracks are designed for creating jigs, fixtures and even track tables for your work shop! Add the intersection kit and you have the ability to make a table top that allows you to move hold downs, clamps and more from end to end without removing them. Track tables are great for framing, pocket hole drilling, pocket hole joint securing, sanding, planing and a whole lot more!



The unique universal, double cut profile pulls double duty since it accepts two types of bolts. The track will accept standard 1/4" hex head bolts and 5/16" T-bolts. This makes this type of track extra versatile and very handy in your workshop. If you don't have either size of these two bolts, both sizes are readily available at most any hardware or big box store. Each track measures 3/4" wide by 3/8" tall which makes milling the slot very easy.

The track can be used in a wide variety of ways including on top of fences for adding jigs and fixtures. The track can also be used by embedding them into table tops or workbenches to give you a long hold down run. The 3/4" x 3/8" also allows you to use the track in a standard 3/4" x 3/8" miter slot like a standard miter bar. Simply attach a few smaller pieces to the bottom of a sled and you're ready to go.

As with the track, the included intersection kit is made from the exact same aluminum material. The intersection kit is designed to give you the ability to cross over fixtures from one end of a table to the other end and change location throughout the table top without removing the fixture. This comes in very handy when framing, sanding, planing and other typical woodworking applications. When securing the track or the intersections kit, you can use the included wood screws by themselves or you can use a polyurethane or epoxy adhesive along with the screws. We typically will only add adhesive when extra clamping pressure will be required. Each track is pre-drilled and counter sunk to comfortably accept the wood screws.

Time to Upgrade Your Workspace!

We all do it. We put off those projects that take a small amount of time simply because its not part of our finished product. What of the that little project could help your finish off your bigger projects quicker and much more efficiently. Building a jig or a track table can help with a wide variety of projects and track table are super easy to build.

MDF, Solid Hardwood, Plywood and More!

Depending on your taste or budget you can make a high quality table top out of most any material you desire! All you really need to do is to keep in mind the thickness of the stock so it can accommodate the track depth. Many woodworkers tend to lean toward MDF since it is solid, easy to mill and is an economical choice.

Ready to Go, Right Out of the Box!

Each track is predrilled and countersunk to neatly fit the included wood screws. This makes installing the track into a table top or jig super easy and much less time consuming. If you choose to add an adhesive for extra holding power, we recommend using an epoxy glue for best results.

Track Dimensions

Each track and the intersection kit tracks are extruded to the specifications shown above. These specs are the perfect guide for cutting slots into a table top surface to install the tracks. The inner dimensions of the track show that our track will work with both 1/4" hex head bolts and 5/16" t-bolts.

×

Mini T-Track

Our Aluminum Mini-T-Track works great for jigs, fixtures and multiple projects on your work bench, router table, table saw and more. Made in the USA, our Mini-T-Track is perfect for all your woodworking operations that need a small mounting depth like the face of a fence.

Pre-drilled mounting holes

Track has pre-drilled mounting holes that will accept #4 wood screw.The mini-T-Track is designed to fit flush into a standard 3/4" x 3/8" miter slot for all your sliding jigs in your table saw or router table.

Install on top of fences

Install on top of fences for stop blocks, flip stops, hold downs and more.

Perfect for embedding into fences

Our Aluminum Mini-T-Track is perfect for embedding into fences to allow for use of many different jobs. With a low profile it can be inlayed into thin material as well as excepting a standard 1/4" x 20 tpi hex head bolt.

×

Heavy Duty T-Track

The Heavy Duty T-Track is great for constructing jigs on workbenches, drill press tables & more. The Heavy Duty Aluminum T-Track has a 1/8" wall which will not bow or twist & allows for everday heavy use. Track has pre-drilled and countersunk holes for mounting. No more hunting for hard to find T-Bolts or special locking pieces. Works with 3/8" x16 hex head bolts which can be found at any local hardware store. Perfect for all your jig and fixture needs that require more holding power. MADE IN THE USA!

Pre-drilled and countersunk holes for mounting

Track has pre-drilled and countersunk holes for mounting. No more hunting for hard to find T-Bolts or special locking pieces. Works with 3/8" x16 hex head bolts which can be found at any local hardware store. MADE IN THE USA!

Perfect for jig and fixtures

Perfect for all your jig and fixture needs that require more holding power.

×

Standard Miter T-Track

When building sleds or fixtures, workshop tables, router table tops or any type of jig or fixture that helps hold stock in place or helps feeding stock through a cutter, miter t track will help make it so much easier. Miter T Track does this by allowing devices like miter gauges to effortlessly slide through the track for cutting applications and it can also accept fixtures with the proper hardware like featherboards to keep your stock firmly against a fence.

A neat fit

The Miter T Track has a “T” shape to it so that it can accept the discs on the ends of many miter gauges. This essentially means that your ¾” x 3/8” bar on your miter gauge will fit neatly into this track even with the disc on the end. Of course you don’t have to have a bar with the disc on the end. Whether you’re making a table top for your router, your band saw or simply building a sled, a standard ¾” x 3/8” thick bar will do the trick!

Easy to Install

Miter T Track is often used in woodworking applications but can be used most anywhere throughout a workshop setting.

Works with Miter Gauges

It is the ideal solution for router tables in need of a miter slot for miter gauges. The ¾” wide slot accommodates most miter gauges which makes it super handy for any workshop.

Works with UHMW Bars

Many woodworkers and professionals alike build jigs or sleds with UHMW bars on the bottom that fit right into this miter track.

Proudly Made in the USA

When we decided to start manufacturing aluminum tracks many years ago (well over 20 years), we thought that it was very important to do our best to keep the manufacturing process here in the United States. We are proud to say that even after 20 years, we manufacture all of our anodized aluminum track (including this Miter T Track) here in the USA. This helps our customers know that not only are they supporting the economy, but also receiving a high quality product.

×

Standard Miter Mini T-Track

The two most commonly used tracks for woodworkers and general workshops are now combined into one ultimate and super convenient track! Having a standard miter track combined with a mini t track allows you to use multiple jigs and fixtures at once or use for quick and easy change-outs. As with all of our tracks, the walls of the track are thicker than off brands each track is proudly manufactured from start to finish in the USA!

A Perfect Match

Miter Track is on of the most commonly used tracks in the woodworking and general workshop industries. It allows the user to slide jigs and fixtures through the track with a smooth sliding action. It works exceptionally well with miter gauges and UHMW bars mounted on sleds or fixtures. The Mini track is perfect for mounting jigs and fixtures to hold work against a fence or to hole work down. Ideal for accessories like featherboards. The track can be mounted to most any table top surface where it is needed.

Easy to Install

The track can be mounted using glue or using wood screws. Simply mill a slot out on your table top to the correct size your ready to install the track. Full installation instructions are included.

Gauges, Jigs, Fixtures, Sleds and More!

Use this track with miter gauges, featherboards, work stops, jigs, sleds, fixtures and a whole lot more. Truly a versatile track that can be used to make your once difficult projects or tasks much easier!

Anodized Heavy Duty Combo Track

Anodized aluminum to stand up to everyday workshop use and abuse. Perfect for most any workshop environment and best of all its Made In The USA!

20 Years and Counting!

When we decided to start manufacturing aluminum tracks many years ago (well over 20 years), we thought that it was very important to do our best to keep the manufacturing process here in the United States. We are proud to say that even after 20 years, we manufacture all of our anodized aluminum track (including this combination track) here in the USA. This helps our customers know that not only are they supporting the economy, but also receiving a high quality product.