Table Saw & Accessories

×

Universal Miter Gauge Fence

When cutting mitered angles with your table saw you always want to make sure that have enough support of your stock when feeding it through the blade. The table saw blade is rotating toward you at a high rate of speed and if your workpiece moves to the side, the result can be scary and downright dangerous. With the help of a miter gauge and with our Aluminum Miter Fence secured to it, you will have full support all the way up to the blade on most of your miter angle cuts.

The Aluminum Miter Fence has been cut at 45 degrees on both ends of the fence. Doing this allows you to get as close to the blade as possible so your workpiece is fully supported throughout the cutting process. Straight cut or 90 degree cut fences have a large gap between the fence and the blade because it can not get as close with the straight cut ends on the fence.

Cross Cut Angles on Your Table Saw

While a simple miter gauge works pretty well when it comes to cutting angles on your table saw, the miter gauge by itself does not offer much support near the blade when making cuts. In steps the versatile and easy to install Fulton Aluminum Miter Fence!

The Perfect Add-On Accessory for Most Miter Gauges

• Works with most any brand of miter gauge
• Even works with old school style miter gauges (some minor miter gauge modification may be required)
• 45 Degree cut fence ends offer maximum support when cross cutting on your table saw
• Includes a sturdy aluminum flip stop for repetitive length cuts so you don't have to keep measuring after every cut!
• Includes a left reading and right reading sticky back tape for left or right tilt saws

Designed to Be Versatile

The Fulton Aluminum Miter Fence has been designed so it will fit most major brands of miter gauges. From the Precision Kreg Fence to the high end INCRA miter gauge systems to most every standard gauge in between, the Fulton Aluminum Miter Fence will likely fit. The mounting slot on the back of the gauge can be used with standard height gauges and the fence can also be flipped upside down so the slot will accommodate lower profiled miter gauges!

Does it Fit Your Old Delta Gauge???

The short answer is, why yes, yes it does! The longer, but not difficult to understand answer is that the fence should fit most older gauges with the holes that are already in the miter gauge head. If there aren't any holes or they just don't line up, we have provided instructions on how to use a block of wood to remedy this or how to modify the miter gauge itself to attach the Fulton Aluminum Fence.

Max Support Every Time!

Many miter gauge fences have flat or 90 degree ends. While this style of fence kind of works, it is not the optimal way of fully supporting your stock piece through the cutting process. The Fulton Aluminum Miter Fence features 45 degree cut ends which allows you to achieve full support all the way up to the blade. This helps prevent pinching or binding while cutting which ultimately helps prevent dangerous kickbacks.

Make your cut and accurately repeat...

When you need to cut multiple pieces to length, nothing is more frustrating than having to move your piece into position, measure and adjust your piece again until you hit your mark. With the Fulton Flip Stop, repeititve cuts on your table saw is super easy and super quick. Simply slide the stop into position, lock it in place, lower the stop and slide your stock piece up against the stop. Now your ready to make precise length cuts each and every time!

Left or Right? In this case, there's no wrong answer.

We have included a left reading tape and a right reading tape. The reason we have done this is simply for the fact that some prefer one to the other and some saws dictate which one you will use. Also keep in mind that you can always flip the tape upside down in relation to the fence so that you can read the tape when looking down on the fence from above.

Many times when we make miter cuts on our table saw, we need 2 or more pieces that are the exactly same length. While using the included measuring tapes that are included are pretty good at this, we have also included a handy flip stop that locks into any location along the length of the fence. This allows you to make repetitive length cuts without worrying if the pieces will end up the same. The flip stop can can simply be flipped it up and out of your way when not in use.

The Fulton Aluminum Miter Fence is made from one, solid piece of extruded aluminum and has the exact same size track on the top of the fence as there is on the bottom. On the back, there is an offset track for mounting the fence to a miter gauge.

The fence can be mounted to low profile miter gauges or standard profile miter gauges simply by flipping the fence over to accommodate your miter gauge. This fence will fit most available after market and factory table saw miter gauges, however some modification may be required. Full color installation instructions are included.