Cutting Solutions

Thin Rip Table Saw Jig

Making repetitive cuts on your table saw is a pretty straight forward process. What if you need a series of narrow cuts that are about an 2 inches or less in width? Doing this can get tricky. You could always reverse measure and keep the off fall piece, but without a guide of some sort that can be inaccurate. The Thin Rip Jig acts kind of like a third hand behind the blade or cutter. With the saw unplugged simply measure from the outside of of the blade toward the tip of the (guide roller) Thin Rip Jig for the width cut you want to make. Once set, secure the Thin Rip Jig simply by rotating the large, easy to grip star shaped knob. After your first cut, reset your stock behind the blade and slide the fence over so your stock piece is touching the guide roller on the Thin Rip Jig. Lock the fence.
›See more product details

×

Thin Rip Table Saw Jig

Making repetitive cuts on your table saw is a pretty straight forward process. Set your fence and feed each stock piece through the blade to achieve the same size each and every time. What if you need a series of narrow cuts that are about an 2 inches or less in width? Doing this can get tricky since you cant get your hands safely between the blade and the fence. You could always reverse measure and keep the off fall piece, but without a guide of some sort that can be inaccurate.

The Thin Rip Jig acts kind of like a third hand behind the blade or cutter. With the saw unplugged simply measure from the outside of of the blade toward the tip of the (guide roller) Thin Rip Jig for the width cut you want to make. Once set, secure the Thin Rip Jig simply by rotating the large, easy to grip star shaped knob. After your first cut, reset your stock behind the blade and slide the fence over so your stock piece is touching the guide roller on the Thin Rip Jig. Lock the fence.



Making your thin rip cuts in this fashion allows you to cut wider boards down without getting your fingers in harms way by keep them away from the blade or cutter.The Thin Rip works much like a feather except that it doesn't exert spring like pressure against the board. This means it can be used to make accurate, repetitive cuts since it's essentially just holding its spot once it is secured.



The Thin Rip Jig has a roller guide bearing on the tip to make feeding your stock through an easy and smooth moving process. The free rotating bearing is made from high quality materials for extended workshop use. The jig fits directly into most any standard 3/8" x 3/4" miter slot. The body is made from a solid piece of aluminum and is adjustable inward and outward from your fence depending on the width of your stock.

The jig can be used on other workshop machinery like router tables with fences and band saws for re-saw applications. In certain cases, when working with larger or longer stock on table saws or router tables, we recommend using two thin rip jigs behind the blade or cutter for extra stability when feeding your stock through.

Close

Safety Note: When cutting thin strips on your table saw you must use a Zero-Clearance inset (sold separately) to prevent the stock from binding between the blade and factory insert.

Accu-Cut™ Expansion Pack

Double the cutting capacity of your Accu-Cut™ with the Accu-Cut Expansion Pack. It connects easily to your Accu-Cut to deliver the same straight, accurate, splinter-free performance on cuts up to 100" long. Make the cuts you need at any length and angle on panels, plywood, and MDF.
›See more product details

×

Accu-Cut™ Expansion Pack

Double the cutting capacity of your Accu-Cut™ with the Accu-Cut Expansion Pack. It connects easily to your Accu-Cut to deliver the same straight, accurate, splinter-free performance on cuts up to 100" long. Make the cuts you need at any length and angle on panels, plywood, and MDF.

Features:

• Double the cutting capacity of the Accu-Cut by adding two more sections of track to make cuts up to 100" long
• Easily and quickly break down panels and plywood with a circular saw at any angle
• Same straight, accurate, splinter-free performance as the Accu-Cut
• Make the cuts you need – anywhere – by taking your saw to the workpiece instead of bringing the workpiece to a fixed saw location
• No clamps needed thanks to anti-slip guide strips that keep the track in place through the entire cut

Includes:

• (2) 26.5" Aluminum Guide Tracks
• (6) Steel Track Connectors
• (8) Accu-Cut™ Guide Strips
• Owner's Manual

Compatibility:

• Kreg Accu-Cut™
• Kreg AAccu-Cut™ Replacement Guide Strips
• Kreg ATrack Clamps

Get more from your Accu-Cut™ with an Accu-Cut™ Expansion Pack with extended-length track guide





-The Accu-Cut is not compatible with the Kreg Plunge Saw.

-Not intended for use with worm drive saws.

-Not recommended for saws with a plastic upper blade guard, as it can affect accuracy.

Consistent, Dependable Performance That You Expect from the Accu-Cut™

The Accu-Cut Expansion Pack brings the same consistent, dependable performance to your projects that you expect from the Accu-Cut – but allows you to guide your circular saw along an even longer aluminum track for support through the entire cut. The anti-slip, anti-chip guide strips extend through all four track pieces to bring the same tearout protection and stability to your cuts, no matter the length.

Transform Your Accu-Cut Into a High-Performance, 100" Track Guide

It’s easy to transform your Accu-Cut into a high-performance, 100" track guide with the Accu-Cut Expansion Pack. Simply connect the two guide tracks to your Accu-Cut whenever you need to make longer cuts. Take your saw and track to your workpiece to make any length cut – anywhere.

Note: -The Accu-Cut is not compatible with the Kreg Plunge Saw.

-Not intended for use with worm drive saws.

-Not recommended for saws with a plastic upper blade guard, as it can affect accuracy.

Close

Features:

• Double the cutting capacity of the Accu-Cut by adding two more sections of track to make cuts up to 100" long
• Easily and quickly break down panels and plywood with a circular saw at any angle
• Same straight, accurate, splinter-free performance as the Accu-Cut
• No clamps needed thanks to anti-slip guide strips that keep the track in place through the entire cut

Includes:

• 2 ea. 26.5" Aluminum Guide Tracks
• 6 ea. Steel Track Connectors
• 8 ea. Anti-Chip/Anti-Slip Guide Strips
• Owner’s Manual

Accu-Cut™ XL

Set your projects up for success by making straight, accurate, splinter-free cuts with the Accu-Cut™ XL Circular Saw Track Guide. It rips, crosscuts, and makes angled cuts up to 100" long in plywood, MDF, and other large panels with accuracy and control.
›See more product details

×

Accu-Cut™ XL

Transform your circular saw into a high-performance, track-guided cutting tool
Set your projects up for success by making straight, accurate, splinter-free cuts with the Accu-Cut™ XL Circular Saw Track Guide. It rips, crosscuts, and makes angled cuts up to 100" long in plywood, MDF, and other large panels with accuracy and control.

Features:

• Break down panels and plywood easily and quickly with cutting capacity up to 100"
• Splinter-free cuts with tearout protection from anti-chip guide strips
• Make the cuts you need – anywhere – by taking your saw to the workpiece instead of bringing the workpiece to a fixed saw location
• Easily attaches to your left-blade or right-blade circular saw, and removes easily
• No clamps needed thanks to anti-slip guide strips that keep the track in place through the entire cut

Includes:

• (1) Universal Saw Sled
• (4) 26.5" Aluminum Guide Tracks
• (6) steel Track Connectors
• (1) Starting Block
• (8) Anti-Chip/Anti-Slip Guide Strips
• (1) Track Indicator Clip
• Owner's Manual

Not intended for use with worm drive saws.

Not recommended for saws with a plastic upper blade guard, as it can affect accuracy.

The Accu-Cut™ Design Makes it Simple to Set Up

The Accu-Cut™ XL guides your circular saw along an extended-length aluminum track that holds the saw steady and keeps your cuts straight. The track guide is designed for simplicity: just mount your saw to the Universal Sled, align the Accu-Cut™ XL track to the cut line, and make the high-quality cuts you need. The anti-chip guide strips prevent splintering and tearout through the entire length of your cut. The same strips also feature an anti-slip surface that holds the track in place without clamps.

Note: The Accu-Cut is not compatible with the Kreg Plunge Saw.
Not intended for use with worm drive saws.
Not recommended for saws with a plastic upper blade guard, as it can affect accuracy.

Close

Featues:

• Break down panels and plywood easily and quickly. Cutting capacity up to 100"
• Splinter-free cuts with tearout protection from anti-chip guide strips
• Easily attaches to your left-blade or right-blade circular saw, and removes easily
• No clamps needed thanks to anti-slip guide strips that keep the track in place through the entire cut

Includes:

• 1 ea. Universal Saw Sled
• 4 ea. 26.5" Aluminum Guide Tracks
• 6 ea. Steel Track Connectors
• 1 ea. Starting Block
• 8 ea. Anti-Chip/Anti-Slip Guide Strips
• 1 ea. Track Indicator Clip
• Detailed Setup and Usage Instructions