Clamps & Accessories

Back to Back Connectors

Attach any two PRO-GRIP™ straight edge clamps to create your own back to back clamps. Then secure the bottom jaw pads to the table top, secure your wood with the top jaw pads and your ready to work. Sanding, gluing and routing are made much easier. Each kit makes two fully assembled clamps. It takes four back to back adaptors per assembly.

Features:

• Attach to any Pro Grip clamps to create a back to back clamp
• It takes four back to back adaptors per assembly
• Kit makes 2 fully assembled clamps
• Secure bottom jaw pads to the table top
• Secure your wood with the top jaw pads

Wide Jaws

More clamping surface area means more stable clamping power for wider and thicker stock and no marring on softer types of wood.The wide jaws fit securely on to the PRO-GRIP™ clamp heads with two wood screws, which are included. The wide jaws work with any PRO-GRIP™ clamp.

Features:

• More clamping surface for wider/thicker stock
• Non marring
• Fits securely on the PRO-GRIP clamp heads
• Works with any PRO-GRIP clamp

90° Head

Turn any of your PRO-GRIP™ straight edge clamps in to a oversized t-square. The large 90 degree head slides directly over the top of the PRO-GRIP™ clamp head, and it fastens securely on to the clamp with two screws (included). Attaching the 90° head allows you to line up your clamp square to the edge of your stock for fast and easy 90 degree cuts.

Features:

• Turn any size PRO-GRIP straight edge clamp into a oversized T-square
• Slides over the top of the PRO-GRIP clamp head
• Fastens securely on the clamp with 2 screws (included)
• 90 Degree head allows you to line up square with the edge of your stock for fast 90 degree cuts

Comfort Grip Handle

The 7" long Comfort Grip Handle fits any PRO-GRIP™ clamp. This extension gives you better leverage to operate the clamp, especially when more clamping pressure is required in the third locking position.

Features:

• 7" Long handle fits any PRO-GRIP clamp
• Better leverage
• Especially when using the third locking position

18" Clamp & Fence Hardware Kit

Create your own fence for your bandsaw, router table or drill press. The fence hardware kit fits the provided 18" PRO-GRIP™ clamp. This kit allows you to attach any shop made fence plate (wood, plastic, etc.) to the 6" tall brackets for a convenient fence system. Create longer fence by adding extra Pro Grip Fence Hardware Kit(PLU#578).

#560 Kit Includes:

• 1 ea. 18" Pro Grip Clamp
• 2 ea. Fence brackets
• All hardware needed to attach to clamp and fence

• 2 ea. Fence brackets
• All hardware needed to attach to clamp and fence

Universal Fence

A convenient fence that can be clamped with cam action is here. Add one or two universal fences to any of your ProGrip guides and you instantly have a tall fence where you need it. Perfect on a bandsaw. Handy on the table saw. Convenient on the router table. T-slots running the length of the fence back and front allows for fastening feather boards, false fence boards and stop blocks.

Features:

• Set up fences for your bandsaw, router table, table saw
• T-slots running the length of the fence back and front

Panel Master Pro System

Create that custom look for your cabinet doors with the Panel Master PRO™ System. Two heavy duty steel handles attach directly to the new 24" PRO-GRIP™ 180° straight edge clamp. This unique system provides you with a rock solid platform to hold your templates to the top of the clamp while your stock is secure in the bottom of the clamp. Use the system for panels and rails or even use it for small parts that need to be routed, keeping your hands away from the cutters. The 180° straight edge clamp has an adjustable handle which rotates so that it doesn't interfere with the table top while running your stock through the router. Available in three different panel styles, choose one or maybe all three may do the trick.

The Panel Master-PRO™ System includes:

• 2 ea. Heavy duty steel handles
• 1 ea. 90° squaring head
• 1 ea. 24" PRO-GRIP™180° straight edge clamp
• 10 piece template set, which will do panels and rail profiles from 10" to 19" wide.

Hinge Mate

A simple to use hinge mortising system, the Hinge-Mate is completely adjustable and will work on virtually any door, door jamb or stock up to 5" wide. Simply clamp the jig to the stock, adjust the slider to the width of the hinge and make the cut. The system can cut hinge mortises up to 2-1/4" wide by 5-1/4" long. The package comes with all the necessary parts including a mortising router bit to make the cut.

Features:

• Adjustable - will work on any door, door jamb or stock up to 5" wide
• Cuts hinge mortises up to 2 1/4" wide by 5 1/4" long

Features:

• 1 ea. PRO-Grip™ Hinge Mate
• 1 ea. Mortising router bit

Featherboard Kit

The Pro-Grip featherboard works on any of the PRO-Grip™ straight edge clamps. The featherboard comes with an attachment kit to secure it to your clamp so there is no play side to side. Use your featherboard on your router table or even you tablesaw!

Kit Includes:

• 1 ea. Featherboard
• Hardware Kit to attach to PRO-Grip™ clamp

Drill Guide Kit

Infinite control over hole center positioning, the possibilities are limitless. Repetitive drilling is no longer a challenge with this setup jig. Just position the guides where you need them along the straight edge clamp and begin drilling with a 1/4" self centering bit!


Note:
Clamp Not Included

Adjustable Guide Combo Pack

The Adjustable Guide Combo Pack is to be used with the PRO-Grip Wide body Guide (Not Included) or any Pro-Grip Straight Edge Clamp (Not Included). Attaching these two accessories to your PRO-Grip Wide Body Guide or Pro-Grip Straight edge Clamp will allow you to perform 90° cuts as well as angle or tapers on large and small sheets of stock. The 360° clamps rotate to allow the pad of the clamp to be secured firmly to your stock without interfering with the cutting process. The Adjustable Guide attachment fits neatly into the built-in track of your PRO-Grip Clamp and secures with two knobs.


It has positive stops built into unit at:
0°, 15°, 22-1/2°, 30°, 45° and 90°.

Includes:

• 1 ea. Adjustable Guides
• 2 ea. 360° Guide Clamps

360° Guide Clamps - 2 Pack

The PRO-Grip™ 360° Guide Clamps can be used with any style PRO-Grip™ Clamp with some disassembly of the clamp. They heads allow for 360° rotation for creating any desired angle with your straight edge clamp.

Click the PDF link and follow step 1 thru 3 in the instructions for disassembling clamp and then add 360° Guide Clamps and your ready to go.

Note:
Click the PDF link and follow steps 1 thru 3 in the instructions for disassembling the clamp and then add 360° Guide Clamps and your ready to go.

Saw Guide Plate

Cut smooth, straight, clean lines with a saw base plate on your circular saw. Attach plate directly to your saw which in turn attaches directly to your PROGRIP™ straight edge clamp. You can leave the plate on your saw for free hand cutting.

PRO-FIT™ adjustable guide bar for Perfect tracking With a new design, the PROGRIP™ Saw guide plate has become even better than before. All the plates are now equipped with the PRO-FIT™ (patent pending) guide bar system. This system has built in adjusters that lock on to the t-track of the clamp for perfect guide plate tracking. The PRO-GRIP™ plates work with any PRO-GRIP™ clamp.

The plate measures: 13- 3/8" L x 7-3/4" W.

Note: Clamp and circular saw not included.

Router Guide Plate

Attach your router to the PRO-GRIP™ router base to cut near perfect rabbets, dado's or any other straight cut you need to make with your router. Made from clear acrylic.

PRO-FIT™ adjustable guide bar for Perfect tracking With a new design, the PROGRIP™ Router guide plate has become even better than before. All the plates are now equipped with the PRO-FIT™ (patent pending) guide bar system. This system has built in adjusters that lock on to the t-track of the clamp for perfect guide plate tracking. The PRO-GRIP™ plates work with any PRO-GRIP™ clamp.

Plate measures: 9"L x 9-3/4"W.

Note: Clamp and Router not included.

Universal Guide Plate

Either your circular saw or your router will fit on this particular base plate. Made from UHMW plastic for a super slick surface. The Universal plate is easy to install.

PRO-FIT™ adjustable guide bar for Perfect tracking With a new design, the PROGRIP™ Universal guide plate has become even better than before. All the plates are now equipped with the PRO-FIT™ (patent pending) guide bar system. This system has built in adjusters that lock on to the t-track of the clamp for perfect guide plate tracking. The PRO-GRIP™ plates work with any PRO-GRIP™ clamp.

The plate measures: 14"L x 9-1/2"W.

Note: Clamp, Router and circular saw not included.

Hardware Kit

Use this hardware kit to build your own custom jigs and fixtures for your PROGRIP clamps. Designed to work in the T-slot of the clamp.

Features:

• 8 T-bolts, 8 washers and 8 connectors
• Build custom jigs and fixtures for your ProGrip clamps
• Designed to work in the T-slots of the clamp