Clamps & Accessories

Universal Edge Clamping for Face Clamps

The Flex-A-Band™ easily fits on to the jaws of most any face frame clamp. The unique design of the Flex-A-Band™ allow the head of the face frame clamp to transfer pressure onto the edge of the material where it's needed. The deeper you clamp on to the edge, the more holding power you gain with the Flex-A-Bands super-grippy pads. This means you can clamp on to most any contour or rounded edge surface. With the Flex-A-Band™ you can now perform one handed clamping on edges that normally would require large, cumbersome and expensive clamps. The band is made from a durable rubber and the band pads are soft and provide excellent gripping power when needed. The band and pads are both no-marring so your workkpiece is left without any irritating marks.

Comes in 2 Pack (Face Clamps not included)

One Hand Edge Clamp

Tightening the clamp and securing the edge are affected by simply twisting the handle. To clamp beading and edging strips to flat panels, a clamp is needed which prevents the material from slipping, does no harm to the clamped surfaces and provides a secure hold while, at the same time, permitting the clamped parts to be realigned if necessary. The maximum pressure applied to the edge is 450-500 lbs; the spindle travel of the pressure plate is 1-3/4 in. Panels of between 3/8" to 2-1/8" thickness can be clamped. Features a compound screw mechanism which allows simultaneous engagement of the top and bottom pressure pads while pressure is applied to the front edge of the countertop. Can clamp surfaces up to 2-1/8" thick. Pressure pads use soft plastic caps for gentle, no-slip clamping. Strong aluminum frame.

Throat Depth: 3"

Clamping Capacity: 2-1/8"

Clamping Pressure: 500 lbs

Spindle Edge Clamp

The Spindle Clamp is ideal edge clamp. Use your K-body or bar clamp to attach it to. Attach your bar clamp to the outside edge, then attach the spindle anywhere along you bar clamp with clamp pad facing the edge and tighten it down to hold your edge. You can also use the Spindle Clamp to help aid in glue-ups or just to support the middle of wide projects. The spindle clamps will prove to be valuable in your work shop. can be used with any bar clamp rail up to a 1/2" thick.



Note: Requires Bar clamp (not included.)

Pinch Dogs

As the old saying goes; “you can never have too many clamps” if you’re a woodworker. This holds especially true when it comes to achieving near seamless or tight fitting joinery. While using long bar clamps or pipe clamps to glue up panels will work, sometimes you may need a helping hand or “pinch” in certain cases to get the seem just right. Using pinch dogs to pull your or “pinch” the panel joint together is an old tried and true method that is still commonly used today.
›See more product details

×

Pinch Dogs

As the old saying goes; “you can never have too many clamps” if you’re a woodworker. This holds especially true when it comes to achieving near seamless or tight fitting joinery. While using long bar clamps or pipe clamps to glue up panels will work, sometimes you may need a helping hand or “pinch” in certain cases to get the seem just right. Using pinch dogs to pull your or “pinch” the panel joint together is an old tried and true method that is still commonly used today.

Lets keep em' together

Many times when we want to hold two boards together we reach for large, cumbersome clamps. While clamps do work of course, there are times when the can be a little overkill. With the Fulton Pinch Dogs, you'll be able to simply tap a pinch dog over a seam between two boards and it will draw the two boards tightly together. You can also use pinch dogs in conjunction with clamps depending on the size of your project.

Just a Few Taps

With just a few taps, you can have snuggly fit boards to form a panel. Once the glue on the panel is dry, remove the pinch dogs and cut off the ends to get rid of any blemishes.

Textured Pinch Dogs

Many other pinch dog brands have a smooth surface. The Fulton Pinch dogs are textured and they are textured to help make sure that the pinch dog won't slip out once it is in the wood. Other brands tend to give and slip over time.

You can never have to many pinch dogs

The old saying goes something like; " you can never have to many clamps". Well, the same goes for pinch dogs, which are essentially clamps in a way. The more you have, the more boards you can "clamp" together to form a large panel.

WIDE FLAT TOP - TEXTURED SURFACE - TAPERED TEETH

We designed the pinch dog with a wide, flat top to offer more of striking surface when tapping it in. The textured surface help keep the pinch dog from sliding or slipping out of the wood once it is tapped in. Each pinch dog has two tapered teeth. The taper is on the inside of the pinch dog teeth. As you're tapping the pinch dog into the wood the tapered teeth draw the two sides toward the center of the pinch dog. This helps create a nice tight seam.

Close

• Made from solid steel to ensure long lasting durability
• Each dog is lightly textured to provide some “bite” so they wont slip out like some of the coated versions you may find.
• Each pinch dog comes to a tapered point on each side to help pull your stock in toward the center of the pinch dog to give the best clamping results possible.