Clamps & Accessories

×

MATCHFIT Dovetail Clamp + X-Pad

MATCHFIT Dovetail Clamps by MICROJIG will revolutionize the way you work with wood. MATCHFIT Dovetail Clamps move through the grooves below the material, allowing you to clamp anywhere, on any surface, without being confined to the edge. Features new rubberized soft-grip handle for better hold when clamping your next project, and expands creative freedom to build extension fences, tables, workspaces, and personalized track systems.

Clamp in two directions with a single clamp.

The X-PAD applies pressure in two directions as you tighten your Dovetail Clamp. The combined forces keep your work-piece(s) flat and eliminate the need for two or more different clamps.

×

MATCHFIT Dovetail Clamps - 2 Pack

MATCHFIT Dovetail Clamps by MICROJIG will revolutionize the way you work with wood. MATCHFIT Dovetail Clamps move through the grooves below the material, allowing you to clamp anywhere, on any surface, without being confined to the edge. Features new rubberized soft-grip handle for better hold when clamping your next project, and expands creative freedom to build extension fences, tables, workspaces, and personalized track systems.

MATCHFIT Dovetail Clamps – the only clamps as free as your creativity.
The breakthrough dovetail clamp arm design gives you the freedom to create your own track grooves using a dovetail router bit to clamp virtually anywhere.

Create clamping tracks virtually anywhere by routing dovetail grooves.
Exert versatile clamping pressure without interfering with the operation by containing the MATCHFIT Dovetail Clamp head arm within the dovetail groove. It expands creative freedom to build:

• Use as hold downs on workbenches
• Mount outfeed extension to tablesaw
• Mount and infeed to tablesaw
• Personalized track systems
• Extend the height of your tablesaw fence
• Extend the height of your bandsaw fence
• Create your own sawtrack
• Create custom fences
• Use with Matchfit Dado Stop (sold seperately) to create perfect-fitting dados, joinery, and inlays with any saw blade, fast.
• and much morehttp://www.ptreeusa.com.

Includes: 2 MATCHFIT Dovetail Clamps.

Note: Only works with 1/2" x 14º Dovetails

Note: Routers, tablesaws, Matchfit Dado, bandsaw fences, K5, jigs, templates and all accessories are Not included.

×

MATCHFIT Dovetail Clamp
with Variety Pack Hardware + X-Pad

Everything you need to make every inch of your shop more functional. With just a standard ½" 14-degree Dovetail router bit (sold separately), you can route your own tracks, eliminating the need for expensive aluminum T-Track. Create jigs and shop fixtures with the incredibly versatile MATCHFIT System. Dovetail Clamps and Dovetail Hardware move through the tracks below the surface, allowing you to create a variety of jigs that move freely, and tighten down anywhere you can route a groove. Create your own fences, stops, hold-downs, and assembly fixtures in a snap. The X-PAD is an upgrade for MATCHFIT Dovetail Clamps that allows you to clamp in two directions at once—achieving in-line clamping with unrestricted clamp positioning. Use the v-groove to clamp round stock with incredible ease. Simply slide the X-PAD fully over the round cap of a MATCHFIT Dovetail Clamp to add a whole new level of functionality. Compatible with the MATCHFIT Dovetail router bit, available in ½", 8mm, and 12mm shanks.

Features:

• Eliminate the need for expensive T-tracks by routing your own clamp tracks
• Endless work-holding possibilities for jigs and fixtures around the whole shop
• X-PADs simultaneously apply hold-down and in-line pressure as the clamp tightens, and secures round stock with ease.
• Combined forces keep your workpieces flat and eliminates the need for two or more different clamps
• Use with spacers to keep your workpiece steady for hand tool work, routing, sanding, any process that requires unrestricted access to the top
• Ideal track hardware for building jigs, sleds for straight line and tapered cuts, tall fences, fixtures, and hold-downs.

Includes:

• 4 each Dovetail Clamp (DVC-538)
• 1 each X-Pad 4 Pack
• 1 each Variety Hardware Pack

Create your own clamp tracks using a router bit.

• Use any standard 1/2"–14º dovetail router bit to create your own clamp tracks.
• The Dovetail Track System is designed to give you all the functionality of T-track—in less time and at a fraction of the cost.

Clamp in two directions with a single clamp.

The X-PAD applies pressure in two directions as you tighten your Dovetail Clamp. The combined forces keep your work-piece(s) flat and eliminate the need for two or more different clamps.

×

MATCHFIT Dovetail Ratchet Clamp AP

Most clamp arms are free to fall down when released forcing you to reset them every time you secure them, but not Microjig’s Ratchet Clamp. Our exclusive “Anti-Pivot” AP Spring holds the arm where you set it. Now you can release the pressure, move your stock, and reclamp without needing to adjust the arm, upside down or right side up. The ratchet mechanism is fast acting; just adjust the arm so the pad in on the stock and pull the handle to set the hold. Every click increases the pressure. Then instantly open the clamp by pressing the release button. The long ratchet handle provides superior leverage making them easy to use for everyone even those with hand grip issues. The positive lock of the ratchet mechanism resists loosening even under heavy vibration such as grinding or routing.

Work Faster with a Clamp Arm That Won't Drop

Microjig’s exclusive Anti-Pivot coil spring lightly holds the arm so it stays where you set it. Right side up or upside down, just release the pressure, change parts or position and pull the ratchet lever to reset the clamp. Fast and easy. This clamp fits into the MatchFit Dovetail groove you make using any standard ½” wide, 14 degree dovetail bit. Or you can save time using our MatchFit Dovetail Bit that automatically rounds over the top edges and leaves the cleanest possible sides.

Works With any Standard 12mm x 8mm T-slot

The MatchFit Dovetail Ratchet Clamp AP not only works with MatchFit Dovetail Tracks but also any standard 12mm x 8mm T-slot/T-track. Does not work with DeWalt track saw guide rails.

Create Your Own Clamp Tracks Anywhere You Can Route

Simply route a groove anywhere you need using a 1/2”–14º dovetail router bit.

Always Ready to Use

Microjig’s Anti-Pivot AP Spring “pre-loads” the clamp arm preventing it from falling when released. Clamp and release over and over without resetting the arm.”

Efficient Ratchet Mechanism

Set the arm and draw the handle to tighten, press the release button to move quickly to the next task.

The Features You Expect

This Ratchet Clamp works in the standard MatchFit Dovetail Grooves you mill and the large clamping face is equipped with a molded pad to protect your work.

×

MatchFit GRR-RIP Clamp - 2PK

Experience unmatched versatility and power with the MATCHFIT Grr-rip Clamp, designed to work seamlessly in any 1/2", 14° groove you cut. With easy one-handed operation, apply up to 150lbs of force, while the large anti-mar pad and quick-release trigger make adjustments effortless and protect your workpieces.

Unmatched Versatility

The MATCHFIT Grr-rip Clamp is designed to work seamlessly with your MATCHFIT Dovetail Tracks. Imagine a world where you can use a clamp virtually anywhere you can cut a 1/2", 14-degree groove. That's the freedom this clamp offers you. From intricate furniture designs to robust cabinetry to weekend projects, this clamp has got you covered

Powerful One-Handed Operation

Don't let its sleek design fool you. This clamp packs a punch with up to 150 pounds of clamping force. With easy one-handed operation, squeeze to apply the pressure you need exactly where you need it.

Protective Anti-Mar Pad

The large anti-mar clamp pad ensures that your workpieces remain in pristine condition. No more worrying about damaging delicate materials. Plus, the grooved design allows you to hold odd shapes in two directions, horizontally and vertically.

Quick Release Trigger

The intuitive release trigger loosens the clamp instantly without breaking your grip. This means you can adjust or remove the clamp without hassle, making your workflow smoother

Generous Clamping Capacity

With a 6-1/4" (158mm) clamp capacity and a 1-7/8" (48mm) throat depth, this clamp is designed to handle a wide range of projects, big or small. 🇺🇸 Quality You Can Trust Designed in the USA, the MATCHFIT Grr-rip Clamp is forged to fit 1/2" wide, 14-degree MATCHFIT dovetail grooves. This ensures a perfect fit and long-lasting durability.

×

MATCHFIT CNC Workholding Kit

Experience the unmatched innovation of the MatchFit CNC Workholding Kit, where the ingenious low-profile design elevates your woodworking without getting in the way of your tools. It is the only clamping system that uses the MatchFit Dovetail System to securely hold stock while you work the top on your CNC, clamping table, jig, or fixture.

Includes:

Quick and Secure Holding On Your CNC

Virtually all CNC machines sold come with two simple hold-down clamps if any clamps at all, leaving you to figure out how to hold parts on your own. No more double-faced tape. Microjig gives you a comprehensive system for quickly and securely holding work on your CNC, whatever cuts you need to make.

Professional Level Workholding

When work needs to be done across the part surface, it must be held by the edges to prevent damage to the clamps and bits. Clamps holding stock from the top is the most common holding method, and this system engages the work top and edge to prevent movement during heavy milling. Microjig’s CNC Workholding kit uses the MatchFit Dovetail Hardware in the spoilboard we teach you how to make to fit your machine bed. This allows most setups to be done quickly with no tools.

Workholding Without Limits

The X-PAD applies pressure in two directions as you tighten your Dovetail Clamp. The combined forces keep your work-piece(s) flat and eliminate the need for two or more different clamps.

Edge Guides

Edge Guides locate along your spoilboard to provide an accurate, low-profile origin point for easy setups, especially when repeating programs. They can also be aligned within any MatchFit Dovetail Groove.

Ring Clamps

Ring Clamps can be placed anywhere along your work table to lock and unlock your parts with just a twist of the wrist. Ring Clamps feature a unique fixed hub to eliminate loosening when in use.

Ramp Clamps

Ramp Clamps use ramps to hold parts applying force in and down to prevent movement and lifting. They feature a clamping edge that moves forward and down along a ramp to provide clamping force in two directions

U-Pad Clamps

Patent-pending U-Pads apply pressure on the top and sides at the same time, preventing both lifting and sliding. U-Pad Clamps provide superior hold for stock up to 1-1/8” (28 mm) thick.